The cove I 320 is the skimmer when it comes to absolute quietness.The cove I 320 is a skimmer for operation inside the filter tank.We recommend the skimmer for marine aquariums from 800 to 2000 liters.The ideal water level should be between 20 cm and 35 cm. Technical data.  Dimensions of the skimmer:    width 370 mm, length 420, height 720 mm    tool-free disassembly   very fast dismantling of the reactor tube by bayonet fitting possibleAn additional 45 mm must be planned for the removal of the foam pot, to the height of the skimmer for installation in the undercabinet technology tank with.Technical data of the pump:UP 5000 skimmer V24    electronic control in 10% steps    20 - 100% adjustable   24 volt safety extra-low voltage    10 volt interface   25mm pipe connections   Pump can be disconnected from controller   24 volt safety extra-low voltage    Power supply is included   Power cord 1.80mControl cord 3m   Dry run protection function   Turns on again after power failure to the previously set value   Power supply MEAWELL power supply 100-240V 50/60Hz Scope of supply:    1 x coveI 320 skimmer   2 x UP 5000 skimmer V24   1 x spare parts set   1 x operating manual for disperser pump   1 x operating manual skimmer pump:UP 5000 skimmer V24The UP 5000 V24 skimmer is a new skimmer pump designed for the highest demands in marine aquaristics.The new 24 volt brushless DC motor allows absolute quiet running and offers the highest level of safety due to the protective extra-low voltage.The maximum output of a UP 5000 skimmer V24beträgt 1200 l/air per hour, at only 30 watts. The controller allows adjustment of air output from 20 to 100% in 10% increments. Also the needle wheel and the venturi nozzle are designed for an absolutely effective and smooth running to meet highest demands. The pump can be disassembled without tools by the bayonet lock on the centrifugal housing.The shaft and plain bearing bushes are made of the hardest durable ceramics. The aging-resistant and vibration-damping silicone bushings, in which the plain bearing bushings are enclosed, ensure very smooth running. We manufacture the needle wheel from POM. Compared to other plastics, the plastic POM has a much higher strength. This makes the needle wheel extremely resistant.

The Cove I-130 is a skimmer designed to operate inside the filter tank. The Cove I-130 DC is powered by our new very quiet UP 2000/1 skimmer V24 pump. operated. These BLDC motor pumps are particularly characterized by their quiet running. . We recommend the skimmer for saltwater aquariums from 200 to 450 liters.. The ideal water level should be between 16 cm and 22 cm. Technical data. Dimensions of the skimmer: Width 180 mm, length 245, height 500 mm Tool-free disassembly of the entire skimmer and pump. very fast dismantling of the reactor tube possible due to bayonet fitting. An additional 38 mm must be added for the removal of the foam pot, to the Height of the skimmer for the installation in the Unterschranktechnikbecken be planned with. Technical data of the pump: UP 2000/1 skimmer V24 (0-22 watts) 24V DC 0 - 22 watts infinitely variable POM Needle carrier 2 meter power cord Low noise and durable due to ceramic shaft and ceramic bearing bushes Scope of delivery: 1 x coveI 130 skimmer 1 x UP 2000/1 skimmer V24 1 x spare parts kit 1 x Dispergator pump instruction manual 1 x skimmer operating manual Pump: Due to the uncomplicated and very robust construction of the UP 2000/1 skimmer, an extremely long service life is pre-programmed.. Due to the exceptionally good performance of this pump series in terms of on water-air intake and energy consumption, it is ideal for this skimmer. The pump is manufactured from selected materials. The shaft and plain bearing bushes are made of the hardest durable ceramic. The aging resistant and vibration dampening silicone bushings in which in which the plain bearing bushes are enclosed, provide for a very quiet running. We manufacture the needle wheel from POM. The plastic POM has a much higher strength than other plastics. strength. This makes the needle wheel extremely resistant.

The cove I 200 is the skimmer when it comes to absolute quietness. The cove I 200 is a skimmer for operation inside the filter tank. We recommend the skimmer for saltwater aquariums from 400 to 1000 liters. The ideal water level should be between 18 cm and 25 cm.   Technical data. Dimensions of the skimmer: Width 242 mm, length 320, height 555 mm. toolless disassembly very fast dismantling of the reactor tube possible by bayonet fitting. There must be an additional 38 mm for the removal of the foam pot, to the height of the skimmer for installation in the Unterschranktechnikbecken with be planned. Technical data of the pump:. UP 5000 skimmer V24 Electronic control in 10% steps. 20 - 100 % adjustable 24 volt safety extra-low voltage 10 volt interface 25mm pipe connections Pump is disconnectable from controller Power supply is included Mains cable 1.80mControl cable 3m Dry run protection function Returns to the previously set value after power failure. Power supply MEAWELL power supply 100-240V 50/60Hz   Scope of delivery: 1 x coveI 200 skimmer. 1 x UP 5000 skimmer V24 1 x spare parts kit 1 x operating manual for disperser pump 1 x operating manual skimmer   Pump: UP 5000 skimmer V24 The UP 5000 V24 skimmer is a new skimmer pump designed for the highest Requirements in saltwater aquaristics was developed. The new 24 Volt brushless DC motor allows for absolute quiet running and offers safety due to the safety extra-low voltage. The maximum performance is 1200 l/air per hour, at only 30 watts. The controller allows an adjustment of the air output from 20 to 100 % in 10 % steps. The needle wheel and the Venturi nozzle are also designed for absolutely effective and quiet running to meet the highest demands. the highest demands. The pump can be dismantled without tools thanks to the bayonet lock on the the centrifugal housing without the use of tools. The shaft and plain bearing bushes are made of the hardest durable ceramics. The aging-resistant and vibration damping silicone bushings, in which the plain bearing bushings are bushes are enclosed, ensure very smooth running. The needle wheel is made of POM. Compared to other plastics, the plastic POM strength by far compared to other plastics. This makes the needle wheel extremely resistant. Further information:  usage_manual_cove_i_200_240.pdf

The cove IS 130 is a skimmer for operation inside the filter tank.We recommend the skimmer for marine aquariums from 200 to 450 liters.The ideal water level should be between 14 cm and 22 cm. Technical data.    Dimensions of the skimmer:   Width 160 mm, length 245, height 500 mm   tool-free disassembly of the entire skimmerAn additional 38 mm must be included for the removal of the foam pot, to the height of the skimmer for installation in the undercabinet tank.Technical data of the pump:    10 watts    POM needle bearing   2 meter power cord   Low noise and durable due to ceramic shaft and ceramic sleeve bearing   transparent gyro housing Supplied:    1 x coveIS 130 skimmer   1 x UP 1000 skimmer   1 x spare parts kit   1 x operating manual for disperser pump   1 x operating manual skimmer pump:Due to the uncomplicated and very robust design of the UP 1000 skimmer, an extremely  long service life is pre-programmed.By the exceptionally good performance of this pump series in terms of water-air intakeand energy consumption, it is ideal for this skimmer. The pump is made of selected materials.The shaft and plain bearing bushes are made of the hardest durable ceramics.The aging-resistant and vibration-damping silicone bushes in which the plain bearing bushes are enclosed,ensure very smooth running. We manufacture the needle wheel from POM. Compared to other plastics, the plastic POM has a much higher strength. This makes the needle wheel extremely resistant.

The Cove I 160 is a skimmer for operation inside the filter tank..   The Cove I-160 DC is powered by our new very quiet UP 2000/1 skimmer V24 pump. powered. These BLDC motor pumps are especially characterized by their quiet running. . We recommend the skimmer for marine aquariums from 250 to 650 liters.. The ideal water level should be between 16 cm and 22 cm.   Technical data. Dimensions of the skimmer: Width 210 mm, length 280, height 525 mm. Tool-free disassembly of the entire skimmer and pump. very fast dismantling of the reactor tube possible due to bayonet fitting. There must be an additional 38 mm for the removal of the foam pot, to the height of the skimmer for installation in the undercabinet tank with be planned. Technical data of the pump:. UP 2000/1 skimmer V24 (0-22 watts) 24V DC 0 - 22 watts continuously variable POM needle support 2 meter power cord Low noise and durable due to ceramic shaft and ceramic plain bearing bushes.   Scope of delivery: 1 x coveI 160 skimmer. 1 x UP 2000/1 skimmer V24 1 x spare parts kit 1 x operating manual for disperser pump 1 x instruction manual skimmer   Pump: Due to the uncomplicated and very robust design of the UP 2000/1 skimmer, an extremely long service life is pre-programmed. Due to the extraordinarily good performance of this pump series in terms of Water-air intake and energy consumption, it is ideal for this skimmer. The pump is made of selected materials. The Shaft and plain bearing bushings are made of the hardest durable ceramic. The aging resistant and vibration dampening silicone bushings in which bushes, in which the plain bearing bushes are enclosed, provide for a very smooth running. We manufacture the needle wheel from POM. The plastic POM has a much higher strength than other plastics. strength. This makes the needle wheel extremely resistant.

The cove IS 120 is a skimmer for operation inside the filter tank. We recommend the skimmer for marine aquariums from 150 to 250 liters. The ideal water level should be between 14 cm and 22 cm.   Technical data. Dimensions of the skimmer: Width 145 mm, length 225, height 450 mm. tool-free disassembly of the entire skimmer. There must be an additional 38 mm for the removal of the foam pot, to the Height of the skimmer for installation in the undercabinet technology basin be planned with. Technical data of the pump:. 10 watts POM needle drag 2 meters power cord Low noise and durable due to ceramic shaft and ceramic sleeve bearing. Transparent gyro housing Scope of delivery: 1 x coveIS 120 skimmer 1 x UP 800 skimmer 1 x spare parts kit. 1 x operating manual for disperser pump 1 x skimmer operating manual Pump: Due to the uncomplicated and very robust construction of the UP 1000 skimmer, an extremely  long service life is pre-programmed. Due to the exceptionally good performance of this pump series in terms of water-air intake. and energy consumption, it is ideal for this skimmer. The pump is made of selected materials. The shaft and sleeve bearing bushings are made of the hardest durable ceramic. The aging-resistant and vibration-damping silicone bushings, in which the plain bearing bushings are enclosed, ensure very quiet running. We manufacture the needle wheel from POM. Compared to other plastics, POM has a much higher strength. strength compared to other plastics. This makes the needle wheel extremely resistant.

Die UP 8000 V24 skimmer ist eine neue Abschäumerpumpe die für höchste Anforderungen in der Meerwasseraquaristik entwickelt wurde.Der neue 24 Volt brushless DC Motor ermöglicht eine absolute Laufruhe und bietet durch die Schutzkleinspannung ein Höchstmaß an Sicherheit.Die maximale Leistung beträgt 2300 l/Luft pro Stunde, bei nur 50 Watt. Der Controller ermöglicht eine Anpassung der Luftleistung von 5 bis 50 Watt in 5 Watt-Schritten.Die Abschäumerpumpe kann an jeden beliebigen Abschäumer angeschlossen werden.Hierbei ist auch das stufenlos drehbare Kreiselgehäuse von Vorteil, da der Anwender frei entscheiden kann, in welchem Winkel er die Pumpe anschließt.Das Kreiselgehäuse wurde in glasklarem ABS Kunststoff abgespritzt.Hierdurch ist der Verschmutzungsgrad der Pumpe, ohne ein aufwendiges Auseinanderbauen des Abschäumers, zu ersehen.Auch das Nadelrad und die Venturidüse sind auf einen absolut effektiven und ruhigen Lauf ausgerichtet um höchsten Ansprüchen gerecht zu werden.Technische Daten: Maße der Pumpe (mit Rohranschlüssen):Länge:186mm Höhe; 152mm Breite: 100mmelektronische Regelung in 5 Watt Schritten5 - 50 Watt regelbar24 Volt Schutzkleinspannung10 Volt Schnittstelle32mm RohranschlüssePumpe ist vom Controller trennbar24 Volt Netzteil ist im Lieferumfang mit inbegriffenNetzleitung 1,80mSteuerleitung 3mWEEE-Reg.-Nr.DE 83382024